| A Cut Above |
 |
 |
| Written by American Competitiveness Institute | |||
| Monday, 30 June 2008 19:00 | |||
A six-step primer on microsectioning techniques.
Microsectioning is a powerful failure analysis technique when coupled with optical or scanning electron microscopy (SEM) because it permits examination of a variety of failures that could not have been seen without this destructive analysis. Some of the areas that can be investigated through microsectional analysis include component defects, thermo-mechanical failures, processing failures related to solder reflow, opens or shorts, voiding and raw material evaluations. The microsectioning process involves the following steps: Step 1. Identify the area of interest (Figure 1). If the sample is an assembly, some adjacent components may need to be removed, as their presence physically may hinder access to the area of interest. A common tool used to remove components and section the area is a variable speed Dremel rotary tool. A cross-section slightly larger than the area of interest is cut out to reduce damage to the adjacent areas.  Step 2. The sample is mounted (potted) to provide a matrix from which a highly polished surface can be obtained without damaging critical areas. The type of potting material will depend on the sample. We use both epoxy and acrylic mounting materials. These systems both incorporate a two-part combination of resin and hardener, the ratio of which will affect the final mount characteristics. Epoxy is used whenever possible because of its lower shrinkage during curing and because the final mount is clear, which allows viewing of internal mount features during polishing. Epoxy’s drawback is that it requires an overnight cure, as compared to the acrylic, which cures in 2-4 hrs. Step 3. The section or sample is held in the appropriate orientation with either a plastic or metal clip to prevent movement of the sample during curing. The supported sample is placed into a molding cup pre-sprayed with a dry release agent to facilitate removal of the mount after curing. The potting material is carefully poured into the cup, taking care to completely surround the sample and minimize entrapped air. Step 4. The sample is placed into a vacuum for approximately 5 min. to ensure the mounting material pulls into all cracks and crevices and to remove any entrapped air. (Figure 2).  Step 5. The sample is progressively ground and polished with silicon carbide (SiC) paper of progressively smaller grit sizes that is fixed to a rotating platen. Polishing techniques can vary, but the objective is the same: to remove the scratches from the previously larger grit paper through a successively smaller grit paper. Final polishing is done with a rotating felt pad saturated with either alumina or diamond slurry (Figure 3).  Step 6. Optical or SEM imaging is used, depending on the failure (Figure 4).  Microsectioning requires good technique to section precisely the area of interest. During failure analysis, only a single sample is available for analysis. Since microsectioning is a destructive test, care must be taken not to destroy critical evidence. The American Competitiveness Institute (aciusa.org) is a scientific research corporation dedicated to the advancement of electronics manufacturing processes and materials for the Department of Defense and industry. This column appears monthly.
|
Columns
| Semblant Warms to New Fluoroolymer Conformal Coating |
|
Months after hinting at a new conformal coating during a paper session at SMTA International, Semblant has officially launched PlasmaShield. CIRCUITS ASSEMBLY editor in chief Mike Buetow spoke with vice president of worldwide sales and marketing Steve McClure last week. |
| Read more... |
| ECTC in Las Vegas |
What happens in Las Vegas at ECTC, doesn’t stay in Las Vegas, it is shared here. This year’s ECTC, or electronics components technology conference, was held in Las Vegas’ Cosmopolitan, May 28-31. |
| Read more... |
Features
| The Impact of Reel Splicing Kits on Setup and Changeover |
Traditional feeder setup using tape-and-reel can drain time. There’s a quick and better way. |
| Read more... |
| Standard Solar Cells vs. Next-Gen Cells: Which is Winning? |
Overcapacity is stalling the rate of improvement, but only for so long. |
| Read more... |
Search
Search
Login
CB Login
Language
Language
Products
GÖPEL Upgrades TOM AOI for Conformal Coatings
TOM system (Teachable Optical Measurement) inline AOI has been enhanced for inspection of conformal coating Maximum PCB size 460 x 400mm. Can be adjusted to specific test requirements. Range of...
TOM system (Teachable Optical Measurement) inline AOI has been enhanced for inspection of conformal coating Maximum PCB size 460 x 400mm. Can be adjusted to specific test requirements. Range of...
