No Counterfeits, No Excuses Print E-mail
User Rating: / 2
PoorBest 
Written by Mike Buetow   
Tuesday, 31 January 2012 17:33



In a move that already is causing no small degree of consternation, President Obama on Dec. 31 signed a new law that places the onus for ensuring all electronics components in all defense products are legitimate squarely on the Pentagon’s supply chain.

The bill, part of the 2012 National Defense Authorization Act, requires that the Department of Defense, the Department of Homeland Security and their contractors “detect and avoid counterfeit parts in the military supply chain.”

Counterfeits have been a known problem for years. (Circuits Assembly has been warning of the issue at least since I came aboard in 2005, and I first reported on the matter way back in 1993.) I was personally told by a QA manager at one prime contractor that no less than a fourth of all the parts in some of its systems were suspected to be faked or otherwise out of compliance. And workshop after workshop told the tale of rivers of parts being shipped as e-waste to China, primarily the Shenzhen area, where they were separated and stripped from circuit boards, cleaned (usually in polluted water), sanded and re-marked, and then resold into the supply chain. In a scintillating keynote at SMTAI in 2010, Tom Sharpe of independent distributor SMT Corp. noted some 29,000 incidents of counterfeits were reported to the US Department of Commerce between 2005 and 2008.

But the turning point, according to some analysts, was a Nov. 8 Senate Armed Services Committee hearing at which Congress heard compelling testimony on the sheer volume of fakes in the US military supply chain, including the results of a Government Accounting Office sting operation targeting electronics parts counterfeiters.

The evidence spurred Committee Chairman Carl Levin (D-MI) and Sen. John McCain (R-AZ) to lead a bipartisan effort to act. The result: legislation that establishes a program of enhanced inspection of electronic parts imported from any country determined by the Secretary of Defense to be a “significant source of counterfeit parts” in the DoD supply chain. The bill further requires defense contractors to establish policies and procedures to eliminate counterfeit electronic parts from their supply chains, and for the DoD to adopt policies and procedures for detecting and avoiding counterfeit parts in its own direct purchases.

Most important, the new law states those contractors that fail to detect and avoid counterfeits, or fail to exercise adequate due diligence, can be debarred. Furthermore, contractors can no longer charge the DoD for rework or related costs to remove and replace counterfeit parts, and they are held liable for any remedies required, regardless of where the counterfeit entered the supply chain. The law affects all contractors at all tiers and is not limited to direct acquisition of parts. In other words, an EMS firm would be responsible for the counterfeit solder mask (yes, that happens) on a PCB it sourced – knowingly or not – from a fabricator in Asia (yes, that happens too).

Counterfeiting runs the gamut from the mundane to the highly sophisticated. In some cases, the trickery is performed by crude re-marking and easily caught by a diligent inspector with an eye loupe. But at the upper end, it has evolved into a wholly systemic problem; again, we have been reporting on the “fourth shift” at various semiconductor factories, where workers build parts using legitimate materials and lines, but those parts are not subject to rigorous inspection and are sold “out the back” to unscrupulous third parties. In one egregious episode, VisionTech Components administrator Stephanie McCloskey was sentenced to three years in prison, and her boss, Shannon Wren, died of a drug overdose after facing similar charges for duping the US government in a long-running scam.

There is no question the supply chain has found counterfeit detection and prevention an expensive and difficult undertaking. XRF, chemical or laser etching, and DNA marking are three of the more sophisticated means, although each adds time and cost to traditional inspection methods.

But the problem is too pervasive, and the risks too great, to whine about the costs. Counterfeiting has gotten completely out of hand. For those reasons, we welcome the bill and its well-conceived structure that puts the onus not on the taxpayer (via pass-along costs), but on the supplier, where it belongs. If this means contractors will have to start relying more on known-good suppliers, well, that’s not a bad thing either. I’ve seen far too many instances of high-level buyers at OEMs and EMS companies searching for parts on LinkedIn to be confident that the auditing many claim to have in place is being taken seriously.

P.S. Join our new LinkedIn Group: EMS – Electronics Manufacturing Services.

Last Updated on Wednesday, 01 February 2012 13:09
 

Columns

Eastern-US: China’s New Competitor?

Parity emerges among EMS Factories from Asia, Mexico and the US.

For the first time in years we see parity in the Eastern US among EMS factories from Asia, Mexico and the US. This EMS market condition will permit American OEMs (the EMS industry refers to OEMs as customers) to have more EMS pathways to choose from. Now more than ever, such EMS assignments will require deeper investigation relating to the OEMs’ evaluation of manufacturing strategies.

Read more...
 
The Human Touch

For those who count on the electronics industry for big feats, it’s been a remarkable couple of years.

Read more...
 

Features

Advances in Concentration Monitoring and Closed-Loop Control

Contaminated bath water skews refractive index results. New technology can accurately measure aqueous cleaning agent concentration.

Read more...
 
Circuits Disassembly: Materials Characterization and Failure Analysis

A systematic approach to nonconventional methods of encapsulant removal.

Read more...
 

Search

Search

Login

CB Login

Language

Language

English French German Italian Portuguese Russian Spanish
 

Products

Panasonic Debuts PanaCIM Maintenance with Augmented Reality
PanaCIM Maintenance with Augmented Reality software provides instant communication and information to factory technicians -- when and where it is needed -- so they can respond to factory needs more...